ISGS WISDOM SOFTWARE DOWNLOAD FREE

Total time in pickup is the total time that the relay read the voltage above the pickup value, not the time the breaker is told to open or actually opens. For example, if buffer 1 is configured to be captur ed on trip. Perform parameter changes using steps 1 through 9 of the standard operating procedure described in Section 3. Tests may be repeated at required settings. A Phase T ime Over-. The dial allows the time-to-trip of the curve to be raised or lowered. Breaker Failure 50BF Relay function that responds to a fault condition where any phase current being measured by a CT does not drop below a programmed level.

Uploader:	Akinodal
Date Added:	11 July 2006
File Size:	65.77 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	25778
Price:	Free* [*Free Regsitration Required]

T ri p LED re-illuminates after r elay is powered up again. Either set can be selected in address block to be the active set that controls the relay operation.

When any of the following symbols appear, read the associated information carefully. Nominal Supply V oltage. Raise the current and note the value of wissom at which the relay trips.

After approximately five sotware, the Power On display is replaced by the Power On Meter display showing two values. The display cursor located next to the address is blinking otherwise repeat step 4. Install the relay M1-type case in the panel opening on the switchgear equipment.

Ground Over current 50HSN Breaker Mechanism Relay function that can be enabled to sense a breaker mechanism error and cause an action to be taken and an event being logged if the a- and b-switches are ever both closed continuously for more than ms. For 5 A CTs, the value ranges from 0.

In addition, the manual offers worksheets for parameter settings, acceptance test procedures, and troubleshooting.

Isgs wisdom software, 8 isgs wisdom software | Siemens ISGS SG User Manual | Page 55 /

Only the level 3 password can set all passwords. Field Service Operation Siemens can provide competent, well-trained Field Service Representatives to provide wiisdom guidance and advisory assistance for the installation, overhaul, repair, and mainte- nance of Siemens equipment, processes, and systems.

Remove the top and bottom connecting plugs paddles. Level 1 and level 2 passwords and can be displayed and changed by entering the respective level password.

For detailed descriptions on how to displayconfigure, save. The relay disabled contact is soctware normally closed contact which opens when the relay is functioning properly.

The Average Current Demand function can be enabled or disabled in this Demand Setpoints function. Prior to placing the relay in service, verify that the correct relay configuration was preloaded at the factory.

If one of the functions is enabled, it causes an alarm if the power factor value leads or lags the setpoint. The Power Setpoints function allows the setting of all power setpoints. Infinity Enter Yes No Table 3.

Contact regional service centers, sales of fices, or the factory. When enabled, the protective function begins monitoring the current flow in the circuit following a trip command by the relay.

Alternatively, set Sofyware might be configured for normal production periods, with set B reserved for construction or periodic shutdown periods. For more information on Wisdom software, refer to Chapter 8.

If power leaves the polarity mark, enter Reverse. The Event Log can be. Apply appropriate value of current for the test.

The 52a and 52b switches r eferred to ar e those. For data port connections refer to Section 2.

ISGS. Intelligent SwitchGear System Operator s Manual firmware version V3. Manual No. SG

The contents of the instruction manual shall not become part of or modify any prior or existing agreement, commitment or relationship. Contact regional service centers, sales offices, or the factory for details. The function is able iegs actuate any binary output contact on pickup, and any trip or binary output contact on trip. Isfs consist of a key membrane keypad, a 2-line bycharacter liquid crystal display LCDthree light-emittingdiodes LEDsand the front port.